··PolskiEnglish
Region and language

Prices include VAT of the delivery country.

CatalogueDelivery and paymentsRequest for quoteConfiguratorsArticles +48 793 996 171
Published: ·8 min read

Heating Cable for Pipes: Frost Protection Guide

How to protect water pipes from freezing: self-regulating or constant wattage cable, sizing for Polish winters, installation, thermostat and the mandatory 30 mA RCD.

Contents
Pipe with heating cable wound under insulation, thermostat and frost

A frozen pipe means more than no water: ice expands and can split a pipe or fitting, and the leak often shows up only after the thaw. The sections most exposed to frost – the water service entering the building, pipes in an unheated garage, basement or loft, the supply to a summer cottage – are most easily protected with a heating cable and a thermostat. This guide explains which cable to choose, how to work out the power you need, how to install it and what protection is required.

Standards and safety requirements

Frost-prevention and de-icing systems fall under HD 60364-7-753 (PN-HD 60364-7-753 in Poland), which covers heating cables and embedded heating systems both indoors and outdoors. Two key requirements follow from it:

  • the circuit supplying heating cables must have additional protection by a residual current device rated at no more than 30 mA – this is a requirement, not a recommendation,
  • heating units without exposed-conductive-parts must be covered by a metal screen or grid; in practice, pipe heating cables have a metal braid connected to the protective conductor (PE).

Heating cables for comfort heating and ice prevention are themselves covered by IEC 60800. Industrial systems, such as trace heating of process pipework, are designed to the EN 62395 series. For RCD types, see RCD types AC, A, F and B.

Self-regulating or constant wattage

There are two main families of pipe heating cable:

FeatureSelf-regulatingConstant wattage (resistive)
Operating principleA polymer core changes resistance with temperature: the colder it is, the higher the outputFixed output per metre regardless of temperature
LengthCut to length from a reel, with a connection kit and end sealFactory-set section length that must not be shortened
Crossing and overlappingAllowed where the manufacturer permits itNot allowed – risk of overheating
Start-up currentHigher on a cold start, important when choosing the MCBConstant
ThermostatRecommended, cuts energy useEssential
UsePipes of varying length, fittings, valvesStraight runs of known length, ready-made kits

Constant wattage cable comes in single-conductor versions (fed from both ends, i.e. a loop) and twin-conductor versions (fed from one end, with a factory end termination). For pipes, the twin-conductor version or a self-regulating cable is more practical, because power is brought in from one end only.

How much power you need: a worked example

Cable output is matched to the heat loss through the insulation. For a pipe with cylindrical insulation the loss is:

q = 2π × λ × ΔT / ln(D / d)

where λ is the thermal conductivity of the insulation (from its data sheet), ΔT the difference between the maintained and ambient temperature, D the outer diameter of the insulation and d the outer diameter of the pipe.

Example for Poland: a PE pipe with an outer diameter of 32 mm, 20 mm insulation (D = 72 mm) with λ = 0.040 W/(m·K), maintained at +5 °C, ambient −20 °C (ΔT = 25 K). Depending on the climate zone, the design outdoor temperature in Poland under EN 12831 ranges from −16 to −24 °C.

  • ln(72 / 32) = ln 2.25 = 0.811,
  • q = 2 × 3.1416 × 0.040 × 25 / 0.811 = 7.75 W/m.

Adding a margin of about 30% for wind, thermal bridges and insulation ageing gives roughly 10 W/m, so a 10 W/m cable is enough here. With thinner insulation, a higher λ or a very exposed spot (for example where the pipe passes through a foundation wall in the wind), a higher-output cable or a second run may be needed. A self-regulating cable's nominal output is stated by the manufacturer for a specific pipe temperature – check it in the data sheet.

Heating cable sizing in the example: heat loss 7.75 W/m, with about 30% margin a 10 W/m cable; 12 m of cable is 120 W and 0.52 A at 230 V.1. Pipe 32 mm, 20 mm insulation, λ = 0.040, ΔT = 25 K1Pipe 32 mm, 20 mm insulation, λ = 0.040, ΔT = 25 K2. Heat loss q = 7.75 W/m2Heat loss q = 7.75 W/m3. About 30% margin → about 10 W/m3About 30% margin → about 10 W/m4. 10 W/m cable; 12 m = 120 W, 0.52 A410 W/m cable; 12 m = 120 W, 0.52 A5. 30 mA RCD and thermostat530 mA RCD and thermostat
Heating cable sizing step by step — figures from the calculation in the article.

Installation step by step

  1. On the pipe, not inside it – in domestic systems the cable is usually laid along the lower part of the pipe and fixed with aluminium tape or ties at the spacing given by the manufacturer. Aluminium tape spreads heat better on plastic pipes.
  2. Valves and fittings – need extra cable length because they lose more heat.
  3. Cable inside the pipe – only a cable the manufacturer designates for this, fed in through a dedicated gland tee. For drinking water, the sheath must be approved for contact with water intended for human consumption; in Poland this is usually confirmed by a PZH hygiene certificate, and minimum hygiene requirements for such materials are set by Directive (EU) 2020/2184.
  4. Insulation – fitted over the pipe and cable together; without it, the cable mainly heats the surroundings.
  5. Connection and end seal – made with the manufacturer's kits, in a box with an appropriate IP rating; the braid is connected to PE.
  6. Thermostat – with a sensor on the pipe or in the air, switching heating on only near freezing.
  7. Labelling and testing – mark the insulation to show electric heating is present and measure insulation resistance before switching on.

A heating cable is not buried in the ground on its own. A buried water pipe should run below the frost line, which in Poland is 0.8 to 1.4 m depending on the region; the cable and insulation usually protect the section entering the building, where that depth cannot be kept.

Supply, current draw and protection

Current draw is small: 12 m of 10 W/m cable is 120 W, so at 230 V I = 120 / 230 = 0.52 A. A self-regulating cable, however, draws more briefly on a cold start, which is why the manufacturer gives a maximum circuit length for each MCB rating – follow that table. The circuit is protected by an MCB and, mandatorily, a 30 mA RCD (or an RCBO), and outdoor boxes and thermostats are chosen with a suitable IP rating. For a comparison of RCDs and RCBOs see RCD vs RCBO, and for IP codes Understanding IP ratings.

Common mistakes

  • shortening or overlapping constant wattage cable, leading to overheating and damage,
  • no 30 mA RCD, or the braid not connected to PE,
  • no insulation, or soaked insulation, so the cable cannot keep up,
  • running all winter without a thermostat and wasting energy,
  • a cable not approved for drinking water installed inside the pipe.

How to choose: checklist

  1. Note the pipe length and diameter, the insulation type and the lowest ambient temperature.
  2. Calculate the heat loss and choose the cable output in W/m with a margin.
  3. Pick the type: self-regulating for varying lengths and fittings, constant wattage for straight runs of known length.
  4. Check the protective braid, approvals and – for in-pipe installation – drinking water approval.
  5. Plan a thermostat, an MCB in line with the manufacturer's table and a 30 mA RCD.

Controls and protection at automatics.pro

To control pipe heating, look at the thermostats and temperature controllers category. The required protective devices are in the residual current devices and RCBO categories, and sealed boxes and enclosures for connections in the Ensto range. The full range is available in the shop.

Frequently asked questions

Can a heating cable be buried in the ground?
A heating cable is not buried on its own; it is laid on the pipe under insulation. A buried pipe should be below the frost line (0.8–1.4 m in Poland), and the cable usually protects the section entering the building.
How much current does a pipe heating cable draw?
Very little: 12 m of 10 W/m cable is 120 W, about 0.52 A at 230 V. A self-regulating cable draws more briefly on a cold start, so circuit length is chosen from the manufacturer's table.
Does a heating cable need an RCD?
Yes. HD 60364-7-753 requires additional protection by an RCD rated at no more than 30 mA for heating cable circuits, and the cable's metal braid is connected to the PE conductor.
What heating cable output does a household pipe need?
For a 32 mm PE pipe with 20 mm insulation at −20 °C the loss is about 7.75 W/m, so a 10 W/m cable is enough with a margin. Thinner insulation or windy locations need more output.

← All articles