Switchgear assemblies to EN 61439: design verification, routine verification, nameplate and declaration
The EN 61439 series defines how low-voltage switchgear assemblies are designed, verified and documented. Who is responsible, the types of verification and which documents the buyer should receive.

A low-voltage switchboard is not just an enclosure with devices. It is an assembly someone is responsible for: it must carry its operating current without overheating, withstand the short-circuit current without damage and protect against electric shock. Requirements for such assemblies are set out in the EN 61439 series (EN IEC 61439 in newer editions; PN-EN 61439 in Poland). Here is what "switchboard compliant with EN 61439" means in practice and what to check at handover.
Parts of the standard: which one applies
| Part | Scope |
|---|---|
| 61439-1 | General rules, always used together with a product part |
| 61439-2 | Power switchgear and controlgear assemblies (PSC): main and industrial boards |
| 61439-3 | Distribution boards intended to be operated by ordinary persons (DBO): typical residential and office boards |
| 61439-4 | Assemblies for construction sites (ACS) |
| 61439-5 | Assemblies for power distribution in public networks |
| 61439-6 | Busbar trunking systems |
A board in a flat that residents can access usually falls under Part 3, while a building's main board operated by skilled persons falls under Part 2. The part affects requirements such as protection against contact and how the board is operated.
Original manufacturer and assembly manufacturer
- The original manufacturer develops the switchboard system (enclosures, busbars, supports, device mounting) and carries out its design verification. For the Legrand XL3 system the original manufacturer is Legrand.
- The assembly manufacturer is the panel builder who builds a specific board from the system following the original manufacturer's instructions, and is responsible for it as a finished product.
The assembly manufacturer puts its name on the board, fits the nameplate and issues the documents. It can rely on the original manufacturer's design verification provided it follows the instructions and stays within the verified configurations.
Design verification
Design verification confirms that a board design meets the standard. It covers, among other things, strength of materials and parts, degree of protection of the enclosure, clearances and creepage distances, protection against electric shock and integrity of the protective circuit, dielectric properties, temperature rise, short-circuit withstand, electromagnetic compatibility and mechanical operation. Depending on the characteristic, the standard allows three methods:
- testing of a sample,
- comparison with a tested reference design,
- assessment: calculation or design rules with appropriate safety margins.
Temperature rise and short-circuit withstand are the hardest in practice, which is why it pays to use systems for which the original manufacturer provides verified configurations and calculation data, such as permissible power loss in the enclosure.
Routine verification
Routine verification is carried out by the assembly manufacturer on every board built, to detect manufacturing faults. It includes:
- visual inspection: degree of protection, clearances, marking, completeness;
- checking connections, especially terminal tightening torques (by sampling);
- checking the protective circuit and the continuity of protective connections;
- a dielectric withstand test and/or insulation resistance measurement as the standard requires;
- checking mechanical and, where needed, electrical operation (interlocks, controls).
The result is a routine verification report that should be handed to the buyer with the board.
Ratings the buyer should specify
| Rating | Meaning |
|---|---|
| Un | Rated voltage of the assembly |
| InA | Rated current of the assembly |
| Inc | Rated current of a circuit |
| RDF | Rated diversity factor: the share of circuit rated currents that can flow simultaneously and continuously |
| Icw / Ipk / Icc | Rated short-time, peak and conditional short-circuit current: the assembly's short-circuit strength |
| IP, IK | Enclosure degree of protection and impact resistance |
| Form of internal separation | For Part 2 boards: how compartments are separated (e.g. 1, 2b, 4b) |
The designer or client should at least give the prospective short-circuit current at the installation point, the environmental conditions (temperature, humidity, location) and the required degree of protection. Without them the assembly manufacturer has no basis for verification.
Nameplate and documentation
Every board should carry a durable nameplate with the assembly manufacturer's details, type designation or identification number, date of manufacture and reference to the relevant part of the standard (e.g. EN 61439-2). The board comes with:
- diagrams and a device list,
- the routine verification report,
- an EU declaration of conformity: a low-voltage switchboard is covered by the Low Voltage Directive 2014/35/EU and the EMC Directive, and conformity is shown by CE marking,
- operating and maintenance instructions, where the board has parts requiring them.
Practical tip: at handover, compare the devices on the diagram with those fitted, and check circuit labels and the nameplate. Discrepancies are easier to sort out before installation than after the board is connected.
Changes after handover
Adding a device or replacing a breaker with a larger one changes the conditions for which the assembly was verified (power loss, busbar current). Whoever makes significant changes takes responsibility for their compliance. For larger extensions, contact the assembly manufacturer or repeat the verification.
Common misunderstandings
- "The enclosure complies with the standard, so the board does too." An empty enclosure compliant with EN 62208 does not make the assembly compliant with EN 61439. The assembly manufacturer is responsible for the assembly.
- "The devices are CE marked, so that is enough." CE marking on breakers covers the devices, not how they are connected, cooled and how the busbars withstand short circuits in a particular enclosure.
- "The installation test report replaces routine verification." Installation verification under HD 60364-6 and routine verification of the board are two different documents with different scopes.
For the buyer the key takeaway is simple: do not ask whether "the devices are good", ask who the assembly manufacturer is, which system the board is built on and which verification documents will be handed over. A reliable panel builder will answer easily, and the answers are worth writing into the order. This also makes later acceptance by the site inspector and the building insurer easier.
Switchboard systems at automatics.pro
The catalogue includes the Legrand XL3 system (from small modular boards to XL3 4000 and 6300 cabinets) and Practibox S modular boards, with busbars, supports and covers, in enclosures and cabinets, modular distribution boards and busbars and power distribution. Read about the build process in manufacturing and assembly of switchgear and start a design in the distribution board configurator.